Search Results

Incorporating tapered roller bearings in finite element and other structural analyses requires special considerations. Tapered roller bearing properties such as induced thrust, induced moment, load zone, and bearing stiffness can substantially affect the results of such analyses. This paper will discuss pertinent tapered roller bearing structural properties, two potential modeling techniques, and several examples on how bearing models were incorporated into structural analyses.

This paper documents the vehicle response of a tractor-semitrailer following a sudden air loss (Blowout) in a steer axle tire while traveling at highway speeds. The study seeks to compare full-scale test data to predicted response from detailed heavy truck computer vehicle dynamics simulation models. Full-scale testing of a tractor-semitrailer experiencing a sudden failure of a steer axle tire was conducted. Vehicle handling parameters were recorded by on-board computers leading up to and immediately following the sudden air loss. Inertial parameters (roll, yaw, pitch, and accelerations) were measured and recorded for the tractor and semitrailer, along with lateral and longitudinal speeds. Steering wheel angle was also recorded. These data are presented and also compared to the results of computer simulation models. The first simulation model, SImulation MOdel Non-linear (SIMON), is a vehicle dynamic simulation model within the Human Vehicle Environment (HVE) software environment.

Trailing axles, otherwise known as tag axles, are utilized in many states to allow heavy duty dump trucks and cement trucks to maximize their capacity. The trailing axle is an additional axle mounted on an arm on the rear of the truck that can be raised and lowered. When lowered, the axle extends the overall wheelbase of the vehicle and increases the total number of axles, thereby allowing for additional load to be carried without exceeding load-restriction regulations. There are multiple manufactures of trailing axles that utilize different suspension designs. One design uses an articulating axle that is mounted to the framework that lowers it. In this study, the sensitivity of this design to tire blowout on one of the trailing axle tires is studied. Testing was conducted that involved initiating a sudden air-loss event by creating a hole in the sidewall of the tire. The handling response of the vehicle was documented with on-board instrumentation and on-board and off-board video.

Heavy duty truck engines are quite difficult to electrify, due to the large amount of energy required on-board, in order to achieve a range comparable to that of diesels. This paper considers a commercial 6-cylinder engine with a displacement of 12.8 L, developed in two different versions. As a standard diesel, the engine is able to deliver more than 420 kW at 1800 rpm, whereas in the CNG configuration the maximum power output is 330 kW at 1800 rpm. Maintaining the same combustion chamber design of the last version, a theoretical study is carried out in order to run the engine on Hydrogen, compressed at 700 bar. The study is based on GT-Power simulations, adopting a predictive combustion model, calibrated with experimental results. The study shows that the implementation of a combustion system running on lean mixtures of Hydrogen, permits to cancel the emissions of CO2, while maintaining the same power output of the CNG engine.

The National Institute for Occupational Safety and Health (NIOSH), in cooperation with the Canadian Forces Health Services Group Headquarters, U.S. Army Tank-Automotive and Armaments Command (TACOM), and the Ministry of Health & Long-Term Care, Ontario (Canada), conducted a test program to evaluate the capability of mobile restraint systems to protect occupants in the patient compartment of an ambulance. This paper focuses on the vehicle chassis behavior and acceleration pulses as seen in each test conducted to support the program. This program consisted of testing one Type I ambulance mounted on a Ford F-350 truck chassis (1994 vintage), and three Type III ambulances mounted on Ford E-350 van chassis (two 1993, and one 1999 vintage). A vehicle-to-vehicle side impact test was conducted using the Type I ambulance with a targeted change in velocity of 27.4 kph (17 mph). A 1984 Chevrolet Sierra 2500 was the impacting vehicle for the side test.

Understanding the complex and dynamic nature of wheel-loader's operation requires a detailed system model. This paper describes the development of a conventional wheel-loader's system model that can be used to evaluate the transient response. The model includes engine details such as a mean value engine model, which takes into account turbocharger dynamics and engine governor controller. This allows the model to predict realistic performance and fuel consumption over a drive cycle. The wheel-loader machine is modeled in LMS Amesim® and the engine governor controller is modeled in Matlab/SIMULINK®. In order to simplify the model, hydraulic loads from the boom / bucket mechanism, steering and cooling fan are modeled as hydraulic load inputs obtained from typical short V-drive cycle. Critical wheel-loader drive cycle inputs into the model have been obtained from testing and have been used to validate the system response and cycle fuel consumption.

Mixture formation in a hydrogen-fueled heavy-duty engine with direct injection and a nearly-quiescent top-hat combustion chamber was investigated using laser-induced fluorescence imaging, with 1,4-difluorobenzene serving as a fluorescent tracer seeded into hydrogen. The engine was motored at 1200 rpm, 1.0 bar intake pressure, and 335 K intake temperature. An outward opening medium-pressure hollow-cone injector was operated at two different injection pressures and five different injection timings from early injection during the intake stroke to late injection towards the end of compression stroke. Fuel fumigation upstream of the intake provided a well-mixed reference case for image calibration. This paper presents the evolution of in-cylinder equivalence ratio distribution evaluated during the injection event itself for the cylinder-axis plane and during the compression stroke at different positions of the light sheet within the swirl plane.

This study aimed to construct driver models for overtaking behavior using long short-term memory (LSTM). During the overtaking maneuver, an ego vehicle changes lanes to the overtaking lane while paying attention to both the preceding vehicle in the travel lane and the following vehicle in the overtaking lane and returns to the travel lane after overtaking the preceding vehicle in the travel lane. This scenario was segregated into four phases in this study: Car-Following, Lane-Change-1, Overtaking, and Lane-Change-2. In the Car-Following phase, the ego vehicle follows the preceding vehicle in the travel lane. Meanwhile, in the Lane-Change-1 phase, the ego vehicle changes from the travel lane to the overtaking lane. Overtaking is the phase in which the ego vehicle in the overtaking lane overtakes the preceding vehicle in the travel lane.

Reconstruction of inline crashes between vehicles with a low closing speed, so-called “low speed” crashes, continues to be a class of vehicle collisions that reconstructionists require specific methods to handle. In general, these collisions tend to be difficult to reconstruct due primarily to the lack of, or limited amount of, physical evidence available after the crash. Traditional reconstruction methods such as impulse-momentum (non-residual damage based) and CRASH3 (residual damage based) both are formulated without considering tire forces of the vehicles. These forces can be important in this class of collisions. Additionally, the CRASH3 method depends on the use of stiffness coefficients for the vehicles obtained from high-speed crash tests. The question of the applicability of these (high-speed) stiffness coefficients to collisions producing significantly less deformation than experimental crashes on which they are generated, raises questions of the applicability.